Log Home Store

Log Home and Timber Framing Chisels, Gouges, Mallets, Froes

Framing Chisels and Corner Chisels

Definition: A tool with a cutting edge on one end of a metal blade, used
in dressing, shaping, or working in timber, stone, metal,
etc.; -- usually driven by a mallet or hammer.

Made at a forge started 100 years ago and done in the traditional manner with no power assisted equipment.
Hand forged lamination of "white" steel and wrought iron then tempered to Rc65.
Handles Japanese Red Oak, double hooped

Blade length approximately 5", overall length 16". You can plane across a flat surface approximately 10" before the handle gets in the way and starts to lift the blade off the work.

Note: Barr leather chisel guards, (shown below) will fit these also. 

$149.85

$116.35

$104.95

$

Robert Sorby from England. 
Designed for North American cabin building.  

Useful for large framing work when working on very deep mortises, where strength of blade is required. Fitted with Ash handle  Handles are double hooped.

All Robert Sorby tools are hardness tested. This  ensures that no soft or brittle tools leave the factory. The hardness differs at various points along the tool. For example, it would be wrong to have the area around the tang at the same hardness as the tip. Its role is completely different. If it were too brittle it would snap under pressure.

Note: Barr leather chisel guards, (shown below) will fit these also. 

$125.95

$98.95

$83.95

$19.95

1 x 17-1/2"

$126.95

Showing 2" leather sheath

1-1/2" x 17-1/2"

$126.95

2" x 17-1/2"

$126.95

Protect your investment with our high-quality, hand-crafted, leather guards. Saddle grade leather is stitched and riveted. Available for framing and bench chisels, slicks and draw knives. Chisel guards come with ABS plastic backing inserts. 

Replacement handle for above Barr Chisels

$7.00

Used to cut cut and trim the corners of a mortise to a precise 90 degree angle and any other situation where accurate square corners are required.

Corner Chisel-Barr 

$159.95

$93.95

This looks a lot like the Sorby corner chisel (also made of Sheffield Steel), however with no name stamped on the tool.
Tang style handle
Double hooped handle.

7-1/2" blade
18" overall length

Currently unavailable...we'll be bring in actual Sorby branded corner chisels in the near future.

Blacksmith forge welds by hand a lamination of "white" steel and wrought iron, then tempers. 
Honed to razor edge.
Socket style Red Oak handle, double hooped (metal ring on end to keep handle from splitting).

Blade Length 3"
Overall 10"

NOTE: We have only a few of these left and have been advised they will no longer be imported into North America. Our best guess if they are best used in shallow mortises, when using softer (Pine, Spruce, Fir), wood and not suitable for whailing away on hard Oak mortises.

$98.95

These stout gouges are designed for log work and will cut for many working hours between sharpening. Strength and balance make this gouge a favorite among log smiths.  

$97.95

$108.95

These gouges have a narrow sweep, (called: "transverse curvature of the blade").
Narrow gouges are generally used to finish and detail cuts and for work on small carvings.
Great for cleaning edge of lateral or notch.
Socket style for good durability.

Mallets

We carry a lot of different mallet types. 
You'll want to read up on each of the styles prior to making a determination. 

st0035-mallet-economy

Good all around economy wooden mallets. 
Should last you for years. 
You'll probably lose it before you wear it out.

Large: 3" x 5" head

Note: Sizes can vary slightly.
Most recently large size was 2-3/4" x  5-1/2".

These Carver's mallets have a urethane head and are guaranteed not to crack or split. The anti-shock quality of the head imparts greater force to your tool. 
The handle is hardwood and the length is 10-1/2".

18 oz. $28.95
(occasionally 20 oz. - same $)

30 oz. $31.75

These fine mallets are made by a family that has specialized in mallets and agricultural implements for over two centuries. 
Heads are fashioned from dense, heavy Japanese hardwoods noted for an ability to withstand impacts. The handles are Japanese White Oak for strength and longevity. 
The hand mallets can be used for hammering on chisels, driving wooden pegs and adjusting joinery. 

Use this tool to move your logs or timbers to their exact position. 
Minimizes risk of cosmetic damage to the log or timber due to the larger face of this mallet. 
Head is metal strapped to prevent splitting. 
Head size is 5-1/4" X 5" X 9-3/4". 
The handle is 36". 
Head weight is 7-8 lbs.
Definition: 
Commander: A heavy beetle or mallet. Used in paving, sail lofts, log home building and timber framing.

$71.95

$15.45